Model Number: EE301-I2C
I2C Interface for Digital I/O Control
for use with all Electronic Loads
Picture is a EE301-DCMI
Control Steps	16 Bit ( 65536 Steps )
Read Steps	12 Bit  ( 4095 Steps )

Price List for EE301-I2C   (Module Only)  

Price List for EE301-I2C-CABLE   (Cable + Power) Connects to LPT1  PC Parallel Printer Port
2 station cable comes with 115 vac power Supply  for (2) electronic loads & (2) EE301-I2C modules

 

All units are huma-sealed to lockout moisture & stop corrosion 

• Specifications <--- CLICK HERE to open / Close               E-Mail Contact for PDF-TECHNICAL FILE

  • ( I2C digital bus control for operation of one Electronic Load )

  • Work with EE301xx / EE151xx Electronic Loads Series only

  • External Power Required 15-24 Volts will operate the EE301-I2C + Electronic Load

  • D to A and A to D  match the speed of Electronic Load I/O Control 

  • I2C Bus Interface I/O Control 

  • Bus Speed ( master control ) up to  400 Khz 

  • Can be used with standard 5 volt I2C microprocessor bus

  • Run (2) two EE301-I2C from one I2C bus 

  • 16 Bit / 65536 Steps  ( Current  Control )   ~ 0.0001 - 0.005 Amp steps / dependent on electronic load model

  • 16 Bit / 65536 Steps  ( Current  Control )   = 0 - 4.0 Volts DC  ( D to A )

  • 6 Multiplexed Channels

  • 2 Aux External Channels 0 - 5 Volts Scaled Input ( call factory for option )

  • Aux 1 Channel can be used for primary cell testing & low voltage testing scaled for 0-6.5 & 0-14 Volts 

  • Aux 2 Channel optional ( call factory for option )

  • 12 Bit /   4095 Steps   ( Voltage read back from Load Current )  ~ 0.01 Volt steps  ( A to D )

  • Current read back scales are  / 0 - 10 / 0 -20 / 0 - 40 / 0 - 80  = Full Scale 4 Volts

  • 12 Bit /   4095 Steps  ( Voltage read back from Load Voltage )  ~ 0.01 Volt steps   ( A to D )

  • Voltage read back scales are / 0 - 50 / 0 - 150 = Full Scale  5 Volts

  • Operation Mode: Constant Current & CC-Pulse 

  • Load Temperature ( Ok / Not Ok )

  • UUT External Temperature Sense ( Optional Probe must be specified at time of order )

  • Cables up to 12 feet long can be used for interfacing from the computer to module

  • Software Control Modes: Constant Current / Constant Power / Constant Resistance / Constant Voltage

  • Comes with Software for I2C-RTD & I2C-OCX Controls ( Runs on Windows 98 / NT / 2000 / XP )

  • Comes with EES-100 Demo Software for control of electronic loads ( Runs on Windows 98 / NT / 2000 / XP )

  • Works with customer or factory wired harness. 

  • Comes with wire harness drawings for interface  ( Cable Drawing ) or use ( EE301-I2C-CABLE )

  • Works with EES-100 Software ( Runs on Windows 98 / NT / 2000 / XP )

Cable can be used with EE301-I2C or EE301-DCMI Model Numbers only. Cable + Power for Loads & Control Modules / Connects to a PC Parallel Port / Supports (2) Electronics Loads & Control Modules / 6' Power cable & 5' Data cable  Use EES-100 Software with this Cable.
Price List for EE301-I2C-CABLE	Cable is a stocked item

Home: Http://www.Exec-Eng.com